Browse all practice questions for the Gas Turbine Systems Technician – Mechanical (GSM) A School Test 4 Practice. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Gas Turbine Systems Technician – Mechanical (GSM) A School Test 4 Practice course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which two things are needed in the combustor during the start cycle?
  • What do igniters receive from the ignition exciters?
  • The turbine main casing provides mounting for which stages?
  • Which option correctly lists a not part of the Bridge Control Unit (BCU) panels?
  • The Bleed Air System draws air from which compressor stages?
  • Which of the following options correctly identifies the RGB as a single-stage, foot-mounted, parallel shaft, vertically offset gearbox with double helical gears?
  • What is the purpose of the damage control system?
  • What does SWBDs stand for?
  • The Machinery Control System (MCS) communicates through which system?
  • Which material type is used for Low-Pressure fuel filters?
  • Which section is the ignition location in a gas turbine engine?
  • What are the components of the Control Air System?
  • Which accessory is not driven by the accessory drive housing?
  • What position does the local remote switch need to be in?
  • What information do the FADC/LOCOP screen indicators provide about the Gas Turbine Generator Set (GTGS)?
  • What part of the FADC/LOCOP allows watchstanders to view operational parameters?
  • Which conditions should be checked during a Gas Turbine Generator Inspection (GTGI)?
  • What are the two stations called on the Full Authority Digital Control/Local Control Panel (FADC/LOCOP)?
  • The high main fuel manifold is constructed from which component?
  • What component can be used for water wash?
  • What is the speed sensitive valve?
  • What is the purpose of the compressor bleed air filter?
  • What are the 3 main concerns in turbine operation?
  • At how many psig does the bypass relief valve operate?
  • Which component in the Start Air System is the air pressure regulator valve?
  • What occurs when SSGTG reaches 12,700 RPM?
  • What is the input voltage to the ignition excitor?
  • Which component is mounted on the excessive drive housing?
  • What system is used to meter and distribute fuel to the engine?
  • What is the purpose of the Gas Turbine Generator Set (GTGS)?
  • Which consoles make up the Propulsion Control System?
  • What 2 analog meters are indicated on FADC/LOCOP?
  • Where is the Full Authority Digital Control/Local Control Panel (FADC/LOCOP) located on the Gas Turbine Generator Set (GTGS)?
  • Where is the electric control plant located?
  • Bleed Air System comprises which stages as its bleed air sources?
  • Where are spark igniters located?
  • If remote control is lost, where can control be maintained?
  • Which component arrangement allows the Primary Air Supply Pack to connect via a quick disconnect?
  • Where is the high pressure filter mounted?
  • Where are the water washes located?
  • What type of valve is the solenoid operated butterfly valve?
  • Which of the following is the backup system in the control architecture?
  • How many feet of paper remain in the printer logger assembly?
  • The gearbox housing and cover, gas producer gear train, and power turbine gear train are components of which assembly?
  • Which assembly directs airflow to the first stage compressor blades?
  • Which valve controls bleed air stages 5 and 10?
  • Why should you water wash the Gas Turbine Compressor (GTC)?
  • Which action does the external overspeed/overtemp assembly perform when thresholds are exceeded?
  • Which statement correctly describes the gas turbine generator set fueling system?
  • Which component switches board isolation?
  • During engine shutdown, what happens to the fuel Shut Off Valves (SOVs)?
  • Which measurement is NOT displayed by the two analog meters?
  • The zone electric system contains how many protected zones?
  • What controls all ships service gas turbine generator operations?
  • The fuel pump is mounted in relation to the Accessory Drive Housing (ADH) on which side?
  • Which assembly includes the gearbox housing and cover, gas producer gear train, and power turbine gear train?
  • Which fluid is injected through the water wash nozzle during RIMSS operation?
  • Which machinery provides centralized control on reduction gears, propeller, and engine?
  • What type of air mask is used by blowing bubbles?
  • Where is the pneumatic starter mounted?
  • How many spark ignitors are used in the ignition system?
  • Where is the Redundant Independent Mechanical Starting System (RIMSS) Allison Model 250C-KS4 GTE located?
  • Which pressure source is used to hold the 5th and 10th stage bleed air control valves closed during water wash or fire stop?
  • What controls air pressure for starting?
  • What is the RPM for the cutout of the engine?
  • Which MCS substance system contains 2 plasma?
  • What is the purpose of the Electric Plant Control Console (EPCC)?
  • What type of filter are the Low-Pressure (LP) fuel filters?
  • The EOOW conducts self-tests per hour at which rate?
  • Which panels are part of the Bridge Control Unit (BCU)?
  • Which assembly directs airflow to the first stage compressor blades?
  • During Redundant Independent Mechanical Starting System (RIMSS) operation, air and fuel are mixed and ignited in what section?
  • Automatic Voltage Regulators (AVRs) control power in a diode or what?
  • How many pressure transducers are there?
  • Which device isolates the Gas Turbine Generator (GTG) module in the event of a fire or leak?
  • Fuel nozzles receive fuel from which valve?
  • Which statement about FADAC/LOCAP is true?
  • How many protective zones are in the zone electric system?
  • Which system provides centralized control for ship survival stability?
  • From the gas turbine engine indicators, which subsystem can be monitored?
  • What voltage does the ignition excitor convert 28 VDC into?
  • Which items are considered major components of the ignition system?
  • Water washing the Gas Turbine Compressor (GTC) removes impurities from which part of the Gas Turbine Engine (GTE)?
  • What controls the fuel flow direction in the HP pumping elements?
  • At what RPM does the engine running indicator come on?
  • Which two parameters trigger the external overspeed/overtemp assembly to initiate a shutdown?
  • The Fuel Feed and Drain System provides a signal to the FADC/LOCOP when the fuel manifold pressure falls below which value?
  • What other systems does the GTG set provide?
  • What does GTGS stand for?
  • The assembly that houses the gearbox housing and cover, gas producer gear train, and power turbine gear train is the
  • Which component provides mounting for the 2nd, 3rd, and 4th stage in the turbine section?
  • Which components are provided to enable connection of a Primary Air Supply Pack (PASP)?
  • Rotor wheels and blades are referred to as what?
  • Which component receives 28 VDC from the ship's No Break Power Supply and converts it to 3,000 VDC?
  • How often should gas generators be washed?
  • The length of paper remaining in the printer logger assembly is described as?
  • When are the fuel Shut Off Valves (SOVs) closed?
  • What type of water is used in the water wash sequence?
  • Which valve handles residual fuel drainage from the combustor after shutdown or a false start?
  • When is FADAC/LOCAP fully operational?
  • Which monitoring system is used by the GTG to monitor the operation of the GTE and gear box?
  • What happens if the vibration monitor detects excessive vibration levels?
  • Which term describes a valve that relieves excess pressure in the fuel system?
  • Which device relieves excess fuel pressure in the fuel system?
  • Spark igniters are in which combustion liners?
  • Which component transmits power from the starting RIMMS to the high-speed reducing gear?
  • Which assembly is enclosed by a thermal blanket in the exhaust inner cone?
  • In the exhaust inner cone, which component is enclosed by a thermal blanket?
  • At what stage is power dropped to semi power loads?
  • At what temperature will the 14th-Stage Bleed Air Valve be fully closed due to CTIT rise?
  • What does the gas turbine generator set fueling system indicate about fuel flow?
  • What does the water wash inject through the water wash nozzle while monitoring the RIMSS?
  • How are alarms acknowledged?
  • In the RIMMS engine, which component houses the compressor?
  • Where is the fuel pump mounted?
  • The EOOW/LU bubble memory provides which type of storage?
  • What is the purpose of the fuel nozzle?
  • What does an ignition lead provide?
  • In the GTGS fuel system, which of the following lists the valve indicators?
  • What holds the 5th and 10th stage bleed air control valve closed during water wash or fire stop?
  • In a gas turbine engine, ignition occurs in which section?
  • Which device is used to drive the boost fuel pump?
  • Which feature allows access to combustion liners without removing the turbine section?
  • The fuel system for the Gas Turbine Engine (GTE) receives its fuel from the ship supply and enters the boost section of which fuel pump?
  • What speed should the GTG maintain while motoring the RIMMS?
  • How can standard and non-standard configurations be generated forward and aft using tie breakers?
  • The Gas Turbine Engine (GTE) is directly coupled to which component?
  • The Speed Sensitive Valve vents until the engine reaches which rpm?
  • Which meter indicates relative general speed?
  • When manifold pressure is below the threshold, which panel receives the signal from the Fuel Feed and Drain System?
  • In the ignition system, what is the function of an ignition lead?
  • What does CTIT stand for in the context of bleed air control?
  • Which GTG monitors the operation of the GTE, gear, and reduction gear box?
  • What does EOOW/LU bubble memory provide?
  • At what temperature will the RIMMS engine shut down?
  • The Transfer Gearbox (TGB) transmits power for starting the Gas Turbine Engine (GTE) drive train from which engine?
  • Which valve indicators are associated with the GTGS Fuel System?
  • Which statement best describes the role of the fuel nozzle in the combustor?
  • Which valve closes the 5th and 10th stage of bleed air?
  • Which system supplies the air for starting the gas turbine?
  • Which console implements communications between the Damage Control Tactical Advanced Computer Work Station (DC/TAC-4) and other consoles, sensors, and controls?
  • EOOW self-tests per hour?
  • What information do the two analog meters display?
  • Which system communicates between DC-4 and sensors and controls?
  • Which panel on the integrated bridge system shows engine speed for propulsion control?
  • What atomizes the fuel in the combustion liners?
  • What happens while starting the RIMS if the emergency stop reaches 13,000 RPM?
  • The Redundant Independent Mechanical Starting System (RIMSS) is associated with which engine model?
  • The RIMSS is located inside the enclosure on top of the reduction gear. Which of the following describes its location?
  • On which component is the lube oil filter mounted?
  • Which is the display panel for operators?
  • Where are water washes located?
  • What transmits power from the starting RIMMS to the high speed reducing gear?
  • The valve that directs fuel flow in the HP pumping elements is which type?
  • What kind of water is used in the water wash sequence?
  • What are the major components of the ignition system?
  • Which RIMMS engine component houses the compressor component?
  • What is the PSI of bleed air start?
  • The 360-degree diffuser on the pneumatic starter exhausts air from the starter to which location?
  • Which component is commonly associated with cooling in turbine systems?
  • Which panel provides propulsion control on the integrated bridge system?
  • How is the Redundant Independent Mechanical Start System (RIMSS) engine started?
  • What temperature must the FADC/LOCOP cabinet be kept below?
  • What equipment can be monitored from the gas turbine engine indicators?
  • What is the exhaust from the turbine section called?
  • What component feeds fuel to the drain?
  • To open the diffuser bleed control valve, the engine must reach which speed?
  • During a start sequence, what engine behavior do the indicators help monitor?
  • What is described as a single-stage, foot-mounted, parallel shaft, vertically offset gearbox with double helical gears?
  • What type of valves are the 5th- and 10th-Stage Bleed Air Valves?
  • What is the primary function of the accessory gearbox assembly?
  • What type of valve feeds fuel to the drain?
  • Which instrument indicates engine speed?
  • Where is the accessory drive housing assembly located?
  • What is the start air pressure?
  • What is the output voltage that the ignition leads carry?
  • What does EPCC stand for?
  • What is the acronym for the human-machine interface used on the system?
  • Which component is used as the starting air source?
  • Which valve drains residual fuel from the combustor at shutdown or after a false start?
  • What allows access to combustion liners without removing the turbine section?
  • Which component is designed to prevent foreign objects from entering the system?
  • Which console implements communications between the DC/TAC-4 and other consoles, sensors, and controls?
  • What component protects the Fuel System from over-pressurization?
  • Under which conditions does the external overspeed and overtemp assembly initiate an engine shutdown?
  • In gas turbine operation, combustion occurs in which section?
  • The Gas Turbine Engine (GTE) is directly coupled to what component?
  • What does the water wash inject through the water wash nozzle while monitoring the RIMSS?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy